Autobend Ab5 Manual
This manual is intended for use in the identification, requisition, and issuance of parts for the Hurco Autobend 7 Gauging System. Parts listed in this manual meet specific critical equipm ent design specification requiremen ts. The use of any non-recommended substitute replacement parts may be the source of added trouble.
Do not assume that if parts look alike, they are the same. The majority of parts have s pecial properties known only by the manufacturer.
The specific parts are the result of particular requirements established by extensive research and testing. There is a continuing program to further improve existing parts.
Many of these improvements cannot be detected by visually comparing old and new parts. For these reasons, it is extremely important that only recommended replacement parts be used. The Wiring Diagrams in this manual are intended as an aid to isolate a malfunction when it becomes necessary to troubleshoot the machine to find the source of a problem.
If you are searched for a ebook Autobend ab5 manual in pdf format, then you've come to the correct site. We furnish complete option of this book in PDF, doc,. Programming and Operations Manual Autobend 7 This manual is for the Autobend 7 control system: (Record Serial Number here) Hurco Companies, Inc. Reserves the right to incorporate any modifications or improvements in machines and machine specifications which it. Programming and Operations Manual.
Maquinas Ferramentas LDA. Amada is a registered trademark of Amada Co. Autobend is a registered trademark of Hurco Companies, Inc.
Copley is a registered trademark of Copley, Inc. Guifil is a registered trademark of Guimaraes & Filho LDA. Hurco is a registered trademark of Hurco Companies, Inc. Ford expedition repair manual pdf. IBM and PC/AT are registered trademarks of International Business Machines Corp.
Komatsu is a registered trademark of Komatsu Ltd. LVD is a registered trademark of LVD Company, n.v.
Loire Safe is a registered trademark of Loire S.A.F.E. Of the Autobend 7 Gauging System. This product was intended to be used by trained operators who create metal bending programs either on the console or an off-line system. These operators then run the programs to bend metal. While running the machines, the operators must use their experience and training to make any necessary adjustments and improve the efficiency of their programs.
Autobend Manual
This safety section describes common problems seen by Hurco Service representatives with suggestions for avoiding or dealing with the problems in a safe manner. However, this information is not an exhaustive description of all of the possible misuses of the machine nor is it a substitute for operator training, skill, and good judgment.
Hurco does not accept any liability for. The Autobend 7 Gauging System owner has several responsibilities regarding safety. First, the owner must read this section of the manual and implement the safety requirements described. Then the owner must be certain that the operators in the shop are properly trained and are using the machine as it was intended to be used. The owner must be certain that the operator assigned to run the Hurco Autobend 7 machine i s trained by Hurco.
If the Hurco trained operator leaves the shop, the owner is responsible for providin g training for the new operator assigned to run the machine. The owner may wish to send operators to Hurco training classes or classes held by distributors.
Refer to t he addresses and telephone numbers in the beginning of this manual for Hurco training sites. If there are no training sites in the vicinity of the shop, call the nearest Hurco facility for information about on-site training or other special training opportunities. The owner must also establish proper procedures to prevent fires and provide approved fire extinguishers to put out small fires. Of course, large fires must be extinguished by professional fire fighters.
As a safety precaution, many shops have regular fire drills so that all employees know their responsibilities during an emergency situation. The Autobend 7 Gauging System was designed to meet a wide range of customer needs. If the owner feels that the machine needs to be modified in any way to meet the special needs of the shop, Hurco recommends that the owner call Hurco Technical Support or an authorized Hurco distributor for modification assistance and a written authorization to proceed. If the owner modifies the machine in any way without Hurco’s assistance and a written authorization, the machine warranty becomes invalid.
In addition, such unauthorized modifications may cause safety hazards that may injure the operator and damage the machine. The owner is fully responsible for any accidents resulting from unauthorized modifications.