Manual For Ecco Pool Filter
Eco Kleer 1.5 HP Pool Pump & Motor - Waterway by Waterway Share: + Add to Wishlist. Product #3976 $ 319.99. 1.5 HP Eco Kleer Above Ground Swimming Pool Pump & Motor by Waterway. Release all air from filter and piping system. See filter owner’s manual. When water source is higher than the pump, pump will prime itself when suction and.
Last Updated: November 26, 2013 to our weekly pool maintenance newsletter! Usually at the beginning of the pool season, when you open your pool, your pump might need a bit of priming. Priming is the act of giving your pump enough water so it will start pulling from the pool. Basically, it’s like giving your pump a motivational pep talk to get it in gear. And now, let’s get started on how to prime a pool pump with these 3 easy steps!
Turn Your Multiport Valve to Recirculate This will bypass the filter system, so that the water comes into the pump, through ONLY your multiport valve, and right back into the pool — never touching the inside of your filter. NOTE: Remove any plugs you have in your skimmer(s) or return jet(s) so that water can flow into your pump. Fill The Pump With Water Open up the If you click this link and make a purchase, we earn a commission at no additional cost to you. By removing the lid (make sure all the drain plugs are in place so that your pump doesn’t leak water). Take your If you click this link and make a purchase, we earn a commission at no additional cost to you. And fill up the pump housing where the basket is. This is priming in a nutshell.
What we’re doing is filling the lines from the skimmer to the pump so that there’s enough water to create suction into the pump. I recommend filling for at least 2 minutes to ensure the water is entering the lines. You can also If you click this link and make a purchase, we earn a commission at no additional cost to you.
And spray water into the pipe directly by pointing the nozzle into the opening inside the pump housing. Any Questions? To be honest, it might take a few tries to prime the pump, but if you’re lucky, you’ll nail it on the first try. You may need to prime the pump during the season too, so this is not just a spring startup thing. Sometimes your pump will run dry (but you should NEVER let this happen).
Perhaps the water level will dip down below the skimmer, or something blocks the skimmer from pulling in water. No matter what the cause, you should do your best to keep it from happening. Running a pump with no water can cause damage to the pump and motor. Happy Swimming!
Is sand making its way into your pool, or have you started to notice a strange slimy feeling or a bad smell coming from the water? If any of these problems are happening to you, it’s probably time to think about replacing pool filter sand in your filter tank. When you first set up your pool filter, you probably thought it was going to be a long time before you’d need to worry about putting in any new sand.
And if your filter has been working properly, it probably has been a while! But now it’s time to learn about removing sand from pool filter tanks and how to replace it with fresh, clean sand that will last you several more years. In this article, you’ll learn a few tips to help you better understand when it’s time to change your sand.
After that, you’ll be introduced to all the materials you’ll need to get started. From there, you can find our simple step-by-step guide, separated into each part of the process to make it easier than ever for you to learn how to change pool filter sand on your own. By the time you’ve finished reading our article, you’ll feel like a pro at taking care of the sand in your filter tank. So what are you waiting for? Read on to learn more about how you can take care of this important maintenance on your own without ever having to call a pool tech.
S ome p eople believe the dirt ier the sand, the better it is for cleaning your pool water. This belief stems from the idea that more dirt particles in the sand will work as additional filtration and will, therefore, remove more contaminants from the water before it hits your pool. Of course, it might sound a little gross to use dirt to filter your pool, and it’s a good idea to keep in mind how contaminated the sand gets when it sits in your filter for years and years without cleaning. Others believe that sand in your filter should be dumped out every year and replaced with entirely new sand annually. This is a little too far on the other end of the spectrum in terms of filtration extremes, however. There is something to be said for leaving your sand where it is for a little while and allowing it to build up a strong resistance to contaminants in your pool water. The best way to go about this is to try to find a happy medium.
Your sand should usually be replaced every three to five years to prevent a lot of very nasty contaminants from taking hold inside the tank while still giving the sand plenty of time to do its job. One of the biggest reasons why you should still think about changing your sand even with other pool owners might not is the cleanliness of your water. While swimming in murky or foul-smelling water is unpleasant, the real threat lies with potential bacteria that could build up inside your filter tank over time. Keep yourself and your family safe by making sure your filter sand stays as clean as necessary for as long as possible. You can also extend the life of your filter significantly by replacing the sand every few years.
When you leave old, dirty sand in place for more than five years, you’re asking for trouble with your filter. It will have to work overtime to take care of the water that passes through the media, and after a while, it’s sure to go out, break, or otherwise cause a problem. On the other hand, if you’re replacing your sand every year, you’re disturbing a filter that’s working fine just the way it is. Leave it alone for a few years unless an issue arises. That way, you won’t have to worry about potentially breaking any internal pieces or replacing any external parts that might get worn out with frequent changes. Keep track of how long your current sand has been in the filter. Most sand will need to be replaced every three to five years.
Sometimes, sand can last much longer. If your water is very dirty, if your pool operates all year long, if you have very hard water, or if you use your pool several times a week every week, you may need to change your sand every one to two years. When sand starts to drift into your pool, it may be time to change the sand in the filter. Filter sand stops working correctly when it begins to form tunnels that water can wash right through. As this happens, the water usually carries sand grains with it into your pool. If your water is looking murky, cloudy, or a strange color, it might be time to change your sand. Algae in your pool may also be a sign that you need to think about some fresh sand, too, although algae may occur from other reasons as well.
You do not have to change your sand every time you backwash. On most modern filters, you won’t even have to add any sand back into the tank at all during a normal backwash. Every now and then you may need to add a scoop or two to even out the pressure in the filter tank. In this section, you’ll learn all about the different types of and equipment you’ll need to change sand in pool filter tanks. The type of filter you have may change this list somewhat, but we’ve made sure to mention everything you might need so you can be more than prepared when the time comes.
Keep everything close by during the sand changing process so you won’t have to walk away and leave any potentially dangerous tools or equipment unattended. Changing sand in pool filter tanks isn’t a dangerous task, but it always pays to be mindful of where your tools are and what you’re doing!. Shop vac – You don’t necessarily have to have one of these, but it will make removing the old sand from your tank much safer and easier, too.
Shop vacs are sold in most home improvement stores as well as some big box stores. With this task, you’ll be using yours to remove all the old sand from the filter tank, and you will then need to empty out the shop vac to safely dispose of the sand inside.
Small plastic cup or scoop – If you don’t have a shop vac, you’ll have to remove the sand by hand. It’s going to take a lot longer, but that doesn’t mean it’s impossible.
Have a plastic cup handy, or use a scoop that’s small enough to fit inside the tank but large enough to remove a decent amount of sand with each scoop. You may still need one of these items to remove any stray sand that your shop vac can’t reach, too. Large plastic bucket or tub – This is optional, but it can be very handy for tossing out old sand or for washing the internals in your filter tank. Any plastic bucket or tub will do. You may be able to find these at home improvement stores or you might have an old one left over from some other product you’ve recently purchased.
Gloves and a face mask – The old sand in your filter tank is dirty and full of contaminants. You didn’t want those contaminants in your pool water, so why would you want them to touch you now? For your safety, be sure to wear gloves and a mask when handling the old sand. It’s a good idea to at least keep the mask on when handling the new sand, too, just so you don’t breathe in too much dust as you’re pouring it.
These items can be found in just about any store. Garden hose – You’ve probably already got a garden hose, but if you don’t, be sure to pick one up before you get started on this job. You’ll need to rinse out the inside of your filter tank, and you’ll also want one handy to help you wash down the internal pieces of the filter too.
This is arguably the most important piece of equipment you’ll need to get this job done!. #20 silica sand or alternative – Pool sand filters are designed to take #20-grade silica sand. Most modern filters can also be used with sand alternatives, like ZeoSand or Filter Glass. These are great options if you’re looking for something a little more environmentally friendly, but if you stick to traditional pool sand, that’s okay too. Be sure to have plenty on hand to refill your tank before you start cleaning.
Replacement o-ring – Depending on your filter, you may or may not need this piece, but it’s handy to have it around just in case. Some filters close with a locking mechanism and a gasket that’s surrounded by an o-ring. As you clean and maintain your filter, you’ll have to open this gasket, and the o-ring will stretch out over time.
You can save yourself a lot of trouble with leaks in the future by replacing the o-ring each time you replace the sand if your filter requires it. Dish detergent – You may need a few drops of dish detergent to soak the internals of your filter tank, depending on how dirty or grimy they are. If they’re not very dirty, you won’t need this, but it never hurts to have some nearby when you’re cleaning pieces of your pool filter. Wrench – You may need a wrench to remove the filter tank from its base or from the hoses that are attached to it. You may also need it to help open the filter tank and get it closed again when you’re finished. Screwdriver – You may need a screwdriver to open your filter tank to access the sand inside.
You may also need it to help remove the internal pieces of the filter tank, but on most newer models, these should be able to be removed by hand. A note on dish detergent: Be absolutely sure the suds and soap are completely washed off of any pieces of your filter before you put it back together. Otherwise, you’ll have suds and foam in your pool! A note on sand amounts: Your filter should have a label or a stamp somewhere on the tank that lets you know how large the tank is.
It should tell you, in gallons, how much sand it holds. If it doesn’t, your instruction manual will tell you. If you no longer have that on hand, you can look up the make and model of your filter tank online to find out how many gallons of sand you need to fill it with. Now it’s time to get started changing pool filter sand. Check out the video above to get a visual idea of how to do this first then you can use the steps below for further information. Each of the steps in this process is outlined below and separated into a different section. This way, if you find the need to take a short break at any point, you’ll be able to pick up right where you left off.
This is also a helpful way to be sure you stay on track and don’t jump ahead to a section you’re not quite ready to work on yet. How to Begin 1. Start by assembling all the parts listed in the section above. Make sure to have everything close by while you’re working so you won’t have to step away or go searching for something. This isn’t an electrical task, but it still may be much saf er if you turn off the breaker that controls your pool while you’re working. This way, no water will splash onto any exposed electrical areas and you’ll be much safer overall.
Although you aren’t required to turn off the breaker, it can also help prevent any damage that might occur to your filter or pump if a valve should get turned to the wrong position or either piece of equipment should accidentally be turned on while you’re cleaning. If you aren’t using your shop vac, get your plastic cup and plastic bucket or tub.
You’ll need to remove the sand one scoop at a time and dump it into the plastic bucket. Be sure to put on your gloves and face mask before you do this so you don’t have to come into direct contact with sand that is contaminated with bacteria and much more. When you’ve exposed the laterals on the bottom of the tank, you can stop scooping. Carefully grasp the central pipe and gently pull the pipe and laterals up and out of the sand. Once again, be cautious so you don’t break any of these pieces. Use your garden hose to add some water back to your filter tank.
Manual For Ecco Pool Filter Parts
You should add enough water to fill about half the tank or just a little less. This will make it safer to pour the sand in without running the risk of damaging the laterals or cracking the filter tank, both of which are potential hazards if you dump a large amount of heavy sand inside the tank. Gently put the laterals back inside the tank. They won’t snap into anything, but they should fit snugly and securely into the bottom of the tank. Turn off the pump once again and switch your multiport valve to rinse. Turn the pump back on and let it run for about a minute.
You’re just waiting until the water you can see inside the tank is clear, so this shouldn’t take very long. Turn the pump off once again and switch the multiport valve to filter. Turn the pump back on. Your pool filter is ready to be used once again. It’s a good idea to let your filter run at least one cycle before you use your swimming pool, just to be sure everything is operating correctly. If you don’t do this, you can risk overloading the filter and causing it to work improperly or to spit sand back out into your swimming pool.
Before you leave your filter to do its job, take note of the pressure reading on your pressure gauge. This is what a perfectly clean filter’s pressure should be. In the future, if you have trouble with your filter, you should remember this number so you’ll know what to aim for. Now that you’ve learned all the steps you need to replace sand in pool filter tanks, you’re probably ready to run out to your backyard and get started working on your pool right away. That’s great!
But don’t forget to take another look at the list of materials at the beginning of this article, too. Although some of them may not be required depending on the type of filter you have, you’ll want to have most of them on hand and readily available to help you take care of the job the right way the first time.
It always pays to have someone else to help lend a hand while you’re cleaning, too. It’s possible for you to complete this task on your own, but it will go a lot quicker and much easier if you have a helper who can hold tools for you and assist with pouring out large quantities of sand. Remember, too, that if you ever feel like there’s a step in this process you can’t complete or there’s something that just isn’t clicking for you, that’s okay. Just call a pool technician to stop by and take care of the job for you. Some pool techs will be happy to show you how to perform these tasks on your own so you won’t have to worry about making an appointment the next time you need to replace pool filter sand. With the information outlined above, you’re already well on your way to a better understanding of your pool filter.
In no time, you’ll be able to change the sand and keep your pool as clean and sparkling as always without the need for any additional help. Copyright © by All-About-Water-Filters.com All-About-Water-Filters.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, All-About-Water-Filters.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links. THIS WEBSITE IS NOT INTENDED FOR THE PURPOSE OF PROVIDING MEDICAL ADVICE All the information, content, and material of this website are for informational and educational purposes only and are not intended to serve as a substitute for the consultation, diagnosis, and/or medical treatment of a qualified physician or healthcare provider.